STAAB 3.0 BILLETT HEAD AND MANIFOLDS , HYPER PUMP ,4.9 HYPER TURB .SOUTHERN ILLINOIS BILLETT CRANK AS IS $60,000 OR WILL FRESHEN FOR $65000 216 409 2405

HYPER 15MM BILLETT PUMP $12,000 216 409 2505

2.0 STAAB BILLET HEAD FOR 619 DEERE MOTOR $20,000 216 409 2505

5.0 HYPER CHARGER JUST FRESHENED BY HYPER $10,000 216 409 2505

The motor is 440 ci, built to run at low rpm for natpa competition. Built by merffeld in Iowa. It is a short block just needs to be assembled and run. Call early mornings or nights, thanks 715-829-4072

We're looking for a 466 IH engine.
Ready to run or not.
With clutch or not.
Don't esitate to contact me, you'll get an answer ASAP.
Thank you.

Luke

'93 Cummins Motor (complete minus turbo) approx. 160,000 miles $1600 obo.

24v Cummins Motor will sell complete, as long block, or with just the parts you need. Pricing will vary depending on how the motor is sold.

476hp and 470 tourqe 360ci bored .60 over
eagle kit with steel crank, cast j heads ported and polished, 650 holley msd dist, scott wires, 8 qt pan dyno sheets avalible. 8 runs nice new block is 1971

moving to a bigger class- engine builder avalible to talk to just call or email at tony@southworthchev.com
715-933-0833

Allison W24 3420 cubes, stock, OX blower, extra block, induction parts comes with CD. Asking $35,000 OBO
Call 269-641-7653

Is a deutz v12 industial engine type: BF 2L 413 Fw

for sale . one of the tops has vaulve damage , is only reson its not runnig.
for sale for only Nkr5000,-

Ford 460, .060 over JE pistons, 4340 H-beam rods, Scat 4.500 stroke crank. Milidon 10qt pan, CSR electric waterpump, MSD distributor and plug wires, Crane solid roller cam, Trickflow aluminum heads, 2.35 int, 1.88 ext, all titanium valves, Crane valvetrain with jomar girdle and tall aluminum valve covers. Trickflow aluminum intake, port matched. 1050 dominator w/ 1" spacer. All parts were new when assembled. Engine has 35 runs on it since built by the engine builder. 13.5 Comp ratio. Dyno sheets available. Engine is available to be heard running. Call Andy - 740-215-4250 $8950. The parts alone cost more than this!

complete motor with turbos. available after murfreesboro pull. e-mail or call 270-392-0359

3x T 55 11D's 3800to 4000+ Hp each.
Fresh dyno sheets
$125K each

AC 670 T long block, has been sitting for a while so it is stuck the block is not cracked though.

JD 8.1 head
cast # R122492
$1,000.00
317-710-6264

Perkin 640 V8 Long Block
Needle Bearing Roller Cam
Ferrea super alloy valves
Manley springs with Titanium retainers/Arias pistons
Total Seal rings
Darton sleeves
Harden rods with ARP bolts
ARP main stud kit

Complete Engines or complete machine shop needs, We have done alot of flowbench and track testing of ported heads, Custom billet rockers that we do in house in ratios of 1.55 through 1.7. Check out our webb site for other jobs we can do for you, Or call 540-432-6560.
Thanks BRMM

500" DRCE II 4.900 Steve Schmidt Racing Engine, Bryant crank, GRP rods, BME pistons, Jesel belt drive/keyway lifters/rocker arms, 60 mm camshaft, HRE intake, 1150 Holley Dominators, Mezierre water pump, Moroso dry sump system/vacuum pump, MSD crank trigger. New rods, pistons, rings, bearings, lifters, and valves. Fresh and dyno tested.

Kyle - 765-717-4360

Hello. Looking for an Allison crankcase in descent condition. Needed to complete a motor.

470 CID Steve Schmidt Pulling Engine. Bowtie Block, Callies Stealth Crank, Oliver Rods, J-E Pistons, ARP Fasetners, Clevite Bearings, Comp Cams Solid Roller, Durabond Cam Bearings, Bronze Lifter Bores, Manton Pushrods, Cast Iron Merlin Heads- Raised Runners, Bronze Guides, Triple Springs, O-Rings, Fully Ported/ Polished & Matched to Fully Ported Weiand Team-G Intake. T&D Rockers, Moroson Covers, Copper Gaskets, Melling H-V Pump, Miloden Pan, 4150 Base Speed Demon, TCI SFI Flexplate, Fluiddamper, MSD Pro-Billet, & Taylor Wires.

760hp at 7200 RPM, Dyno Sheets Available. Will Easily Make 800+hp With Dominator. $17,000+ In Parts/ Labor. Asking $10,999.

Contact: bwb81@hotmail.com.

For sale 2 aries 10 litre engines 644ci and one 636 all complete from manifold to pan 28,000.00 each need to shead some weight on the studmule unlimited pulling tractor changing to all 8.3 engines call 214-736-3200 m-f 7to5 ask for billy or email txmeter@aol.com thanks for reading my add!!!!!!!!!!!!!!!!!!!

This came out of a corvet 427 chevy the best heads in cast 650 HPs. Old school hillborn injection on alcohol.

Virgin TFX 96 block, AJ fuel heads, stage 5 rockers,Bryant billet crank with Brooks B2 rods and arias pistons. TFX oil pump MSD pro mag 44 with a SSI F2 dual gear 14-71. Gorr fuel sysem, too much to list also many parts come with and tools. Would be willing to trade for parts to put a 3 engine chevy together.
thanks
4029201915

2- Allison, V-1710, best of every thing, set up for region & state, one fresh, one with 10 runs , $27,000 each

1- Allison, W 3420 and extra parts, $26,000


Any sensible offer considered on above items


TED BOYER
PHONE: 574 215 8100
PHONE: 574 215 7653

Complete engine – top to bottom.
640 cu in BBC tall deck bowtie block, Callies 4.750 crank, Oliver 6.700 rods, Bullet roller cam, Stefs dry sump oil pan, JE Pistons, Dart 18 degree Big Chief heads, titanium intake valves, sheet metal valve covers, T&D roller rockers, Crower roller lifters, Dart intake, Enderle Bird catcher injection, Enderle front cover, Enderle 80A mechanical fuel pump, Mallory Super Mag III ignition with a Dunn Offset. Dyno and Head flow sheets available.$16,000

Looking for six stock Allison V1710 pistons w/ square top compression ring land. Two main bearings, Good rods G6????? I know.
Also sps or 100 series rod bolts.

904 588 6380 cell lv msg.
or email Thanks

526 Veney motor 4.310 by 4.500 crank has 25 passes road pistons and everything in heads 2.500 heads has 3 60 foot run in a funny car motor can be started and ran for the buyer complete 1471 littlefeild hihelix not a retro blower no mag but has mag drive off set blower belt rcd drive mag in buzzard blower bag pluger oil pump 3 run on it since new tfx 96 cast block has 3 windows and 2 saddles motor is complete can buy with 44 amp mag for extra $$ also waterman fuel pump much more call with question motor needs to go Call with question 20,000.00 o.b.o Call Carl Cell phone 302-463-5381 motor comes with all spares extra cam a couple of spare lifter ,pushrods,adjuster on head spring changers spander wrenches 2 of them and other misc veney tools all i have for this combo

$12,000
1065HP, 835Ft/lb
Dart 9.8 Block 4.25” stroke, 4.625” bore
Reher-Morrison 14.5 degree (OLDS) Big Chief heads with titanium valves (fresh, just back from machine shop)
JE 14.1:1 Compression gas ported pistons
Oliver Billet rods
Callies Stealth Crank
Custom ERSON Roller cam and new Comp Lifters
Single 4 barrel Rupert Gas Dominator on ported Dart Big Chief intake.
T&D shaft rockers
Jesel belt drive Timing
Moroso Vacuum Pump
MSD Billet Distributor with Crank Trigger
Barnes 5-stage Dry-sump Oil system with Stefs oil tank
9" Coan Converter

Will be sold complete including carb, spacer

Brent Foster
304-312-9283

for sale nqs stock altered engine has aftermarket block with all new internals.

for sale nqs stock altered engine has aftermarket block with all new internals.

for sale is a complete nqs stock altered engine has after market block all new internals

This motor dynoed at Mandolini's with a normal Crane cam and modded K-11 superman made 2606hp w/ low ratio BAE rockers. I have the dyno sheet, Ex Tim Stephens IHRA TAFC motor that went 5.72.

526 cid, approx 12:1 cpr (Was going to check exact ratio in a week or two at Rage fuel systems) 4.375" stroke, 4.375" Bore
BAE +.100 tall billet block. 2" spread lifters, 1 window from faulty rod, repaired and run plenty since, did not get into the main or oil pump areas at all. Short block was freshened and not run since.
Bryant billet crank w/ no cracks
New Main/rod bearings
New +.220 rods
New JE pistons+Trend pins+pin buttons+C&A/A&C rings
Billet $1700 cam, Tool steel 2.125" 295-500-16-48, 4-7 and 2-3 swap, with special exhaust lobe (Thacker spec 277mph in TAD)
Crane .904 Lifters
New Casale gear drive
PSI Titanium crank hub
Fuel pump hex drive
BAE fuel pump extension
New taper hex shaft to drive fuel pump for larger hex on cam gear
New Flat out head gaskets
Total flow large valve billet fatheads w/ all Ti Victory 1 valves, triple springs approx 400 psi on seat, (repaired from torching, 2 inner head studs king certed) ran 5.40's in A/Fueler and slightly outflow a BAE 5 head. Small cosmetic potholes in 1 chamber, called BAE and Total flow and it is no problem but could be repaired if you replaced the seats after welding.
Mag drive clamp and stud w/ nut

Spares included:
Bryant 4.375" Crank
3 New JE pistons (Same as in motor)
6 New Ross pistons (Very similar and previous pistons used in this combo)
30-40 Spare Trend wrist pins (Most if not all are new)
Boxes of new piston rings
Bag of new pin buttons
small bag of used magnesium pin buttons
17-18 spare sleeves (All new I think)
3 bolt cam gear in case you go to a normal cam
2 spare PSI degree rings
Box of spare valves, Most are good for emergency use a couple are really nice
New spare set of Flatout head gaskets
There is a ton of money in this setup. $15,000+sh.

Optionally available is:

A used but good shape set of dragster upright zoomies that fit these heads for sale as well $300 (have had some repairs but are not worn out, coating is off where repairs where made but doesn't look horrible. I would have them re coated to make pretty.

Reactor flywheel, another spare Reactor flywheel (Both w/ ring gear) ARP Bolts, and torque convertor adapter available. $200

MSD Pro Mag 44 generator, cap adapter, cap, and rotor. Works great, It was our spare and we need the cash more. $1500 (Save $600 over a new unit)

If your needing a Funny car/altered chassis, PSI inlet shoes, gages, ect....I have them as well.

Thanks,
Trevor Sherwood
727-364-4368

FOR SALE:
JDBB 680ci engine. Dyno tested, 3 runs, like new. REI billet crankshaft, REI billet rods, Arias forged pistons, adjustable timing gears, billet steel roller camshaft(cammed for 4.2 to 5.150 turbo), tall lightweight roller lifters, SMI billet iron V4.0 cylinder head, jumbo high-strength roller rockers, and aftermarket rocker arm assembly. Billet aluminum valve cover, center load exhaust manifold, front load or center load intake manifold. Fluid Damper with pulley drive shaft. Billet aluminum pump bracket, Aviaid 2 stage engine-one stage turbo-one stage fuel pump, 8 gallon 2 pickup steel oil pan. 1200psi water injection pump, 9 nozzle, and Simpson valve. Ready to install in frame. Asking $75,000
Phone Mark at: 715-384-2669

http://www.staabmachine.com/wp-content/uploads/2010/07/20140603_095340-Copy.jpg

500 C.I.
JP1 Cast Block Never Windowed
BAE 5 Early Billet Fuel Heads Fresh (NEW Seats, Titanium Valves, Locks, Retainers, & Manley Springs)
New Black Rocker assembly with Fuel Shafts, Stage V Roller Intake & Exhaust, 7/16 Adjusters
Bryant Crank
(New) BME Rods & Pistons
(New) Crane Cam
Crane Lifters
Dan Olson Dragster Pan
Billet Oil Pump
Magnesium Intake
SSI 1471 Hi-Helix Retro C Rotor with Blower Restraint
Enderle B&U Injector & K Valve
(New) Areomotive 17 Gallon Fuel Pump
Casale Front Drive
Pulleys from 27-45 Tooth 13-9 to 14 MM
Dunn Mag Drive (Fresh)
MSD 44 Mag, Points Box, Coil & Plug Wires
(New) 3 Coated Sets of Headers to go with it Different Sizes.
Call or E-mail for Price
580-512-5578
CopelandRaceCars@aol.com